Click Install. Step4 The Ready to Install the Program window appears, Click Install. The ground wire should always be connected first and disconnected last. Default settings are in square brackets ''. Source
Press Enter to display the setup prompt. 6. You can perform the initial configuration for the entire stack on any switch in the stack. The EN LED for the USB console port turns green, and within a few moments a pop up window stating “Installing device driver software” appears. To configure it later, enterno. http://www.cisco.com/c/en/us/td/docs/switches/lan/cisco_ie2000/hardware/installation/guide/ie2000_hig/HGCLISET.html
See the “Installing the Cisco Microsoft Windows USB Device Driver” section. Yes No Feedback Let Us Help Open a Support Case (Requires a Cisco Service Contract) Related Support Community Discussions Share Information For Small Business Midsize Business Service Provider Industries Automotive Consumer Statement 1001 Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. See Figure 4-12.
See Table 3-1 . Using the Add Remove Programs Utility Using the Setup.exe Program Using the Add Remove Programs Utility Before You Begin Disconnect the router console terminal before uninstalling the driver. Note Disconnect the router console terminal before uninstalling the driver. Cisco Usb Console Driver Mac Figure 4-2 Cisco 1940 Series Chassis Airflow Setting the Chassis on a Desktop You can place Cisco 1900 series routers on a desktop or shelf.
Step3 The Cisco Virtual Com InstallShield Wizard begins. Cisco Usb Console Driver Windows 10 Would you like to enter the initial configuration dialog? [yes/no]: yes At any point you may enter a question mark '?' for help. The USB console port LED turns green, and the Found New Hardware Wizard appears. my company Excessive weight on top of the router could damage the chassis.
Step 2 Remove the rubber feet from the router. Cisco Usb Console Unable To Open Serial Port The USB console port LED turns green, and the Found New Hardware Wizard appears. Safety Messages Warning Do not work on the system, or connect or disconnect cables during periods of lightning activity. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
Step2 If using 32-bit Windows Vista or Windows 7, double-click the setup.exe file in the Windows_32 folder. imp source Failure to stabilize the rack can cause the rack to tip over. Cisco Usb Console Driver Download Click Next. Cisco Usb Console Putty Step 3 Remove the negative and positive screws from the terminal block.
Step 5 When the InstallShield Wizard Completed window appears click Finish. this contact form You can mount the router in the following ways: Front mounting—Brackets attached at the front of the chassis with the front panel facing forward. Uninstalling the Cisco Microsoft Windows XP, 2000, Vista, 7, 8, and 10 USB Driver Note: Disconnect the switch console terminal before uninstalling the driver. 1. See the “Installing and Removing a Redundant Power Supply Adapter” section before connecting to a backup power source. Cisco_usbconsole_driver_3_1.zip Download
Save the covers for reinstallation after you finish wiring. The following cables and adapters may be used for connecting your router to a console terminal, PC, or modem: •USB Console cable—USB 5-pin mini Type-B to USB Type-A. To ensure that power is removed from the DC circuit, locate the circuit breaker for the DC circuit, switch the circuit breaker to the OFF position, and tape the circuit-breaker switch http://socialmedialab.net/cisco-usb/cisco-usb-serial-driver-windows-7-download.html Statement 1028 Table 3-3 summarizes DC wiring requirements for all Cisco 3925 and Cisco 3945 routers.
Note The installation must comply with all required electrical codes applicable at the installation site. Cisco Usb To Rj45 Console Cable Default settings are in square brackets ''. Step4 The Ready to Install the Program window appears.
Cisco serial transition cable that matches the signaling protocol (EIA/TIA-232, EIA/TIA-449, V.35, X.21, or EIA/TIA-530) and the serial port operating mode (DTE or DCE). Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. After you complete the setup program, the switch can run the default configuration that you created. How To Connect To Cisco Switch Using Usb Console Cable Step1 Obtain the file cisco_usbconsole.zip from the Cisco.com web site and unzip it.
Statement 239 Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Step4 The Ready to Install the Program window appears, Click Install. Operating the unit without the cover in place will invalidate the safety approvals and pose a risk of fire and electrical hazards. Check This Out Was this Document Helpful?
The USB console port LED turns green, and the Found New Hardware Wizard appears. Click Next. Power Connections Warning Read the installation instructions before connecting the system to the power source. You can configure the switch as a command switch later through the CLI, Device Manager, or the Cisco Network Assistant application.
Step3 When the Program Maintenance window appears, select the Remove radio button. Statement 1037 Warning Avoid using a telephone (other than a cordless type) during an electrical storm. All connections must be removed to de-energize the unit. Installing the Cisco Microsoft Windows USB Device Driver The first time a Microsoft Windows based PC is connected to the router, a USB driver must be installed.
This section describes how to connect a console terminal or PC to the console port and how to connect a modem to the auxiliary port. interface FastEthernet1/3 ! ...(output abbreviated) ! The attachment points are shown in Chassis Ground Connection on the Cisco 1905 and Cisco 1921 Routers and Chassis Ground Connection on the Cisco 1941 Router. Click Next.
Click Next. Step 2 Double-click the file setup.exe.