This book contains many real life examples derived from the author's experience as a Linux system and network administrator, trainer and consultant. will take like 8 hours but it will be worth it to get this card working. Next to Net device, use the pull-down menu or type in the device name of the client adapter. The card is keyed so it can be inserted only one way into the PC card slot. Source
Scott metalpenguin View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by metalpenguin 06-26-2004, 07:56 AM #2 finegan LQ Guru Registered: Aug Im on dial up know thou, so might take a week to d/l Scott metalpenguin View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts Please visit this page to clear all LQ-related cookies. Are you new to LinuxQuestions.org? http://www.cisco.com/c/en/us/support/docs/wireless/aironet-340-wireless-pc-card-adapter/8127-linux.html
You must be logged in as root or have equivalent superuser privileges. In order of ease one of these will work: 1. Find More Posts by finegan 06-26-2004, 11:53 AM #11 metalpenguin LQ Newbie Registered: Jun 2004 Location: Omaha, Nebraska Posts: 14 Original Poster Rep: I do tar xvzf linux-acu-driver-v21.tar.gz as When the script has finished installing the files, press Enter to continue.
Install on Red Hat 7.1 Red Hat 7.1 includes PCMCIA support in the 2.4.2-2 kernel by default. When the window pops up I get this warning error "eth0 has an alias to module airo_cs in modules.conf, instead of currently loaded module airo!" after clicking on "ok" I then Leave a Reply Click here to cancel reply. On Red Hat and other distributions that include the linuxconf utility, you should use this utility to set the IP address of the computer.
LinuxQuestions.org > Forums > Linux Forums > Linux - Hardware Cisco Aironet 340 wireless card problem User Name Remember Me? Page 1 of 2 1 2 > Search this Thread 06-23-2004, 07:19 PM #1 metalpenguin LQ Newbie Registered: Jun 2004 Location: Omaha, Nebraska Posts: 14 Rep: Cisco Aironet Add /opt/cisco/bin/ to your path. An IP address can be obtained dynamically via Dynamic Host Configuration Protocol (DHCP) or can be statically configured.
The install script prompts you for the name of the web browser to use to display help files. Related Information Cisco Downloads for Wireless Products Technical Support & Documentation- Cisco Systems Contributed by Cisco Engineers Was this Document Helpful? View Documents by Topic Choose a Topic Cisco Aironet 350 Mini-PCI Wireless LAN Client Adapter Cisco Aironet 350 Wireless LAN Client Adapter Cisco Aironet 340 Wireless PC Card Adapter Cisco Aironet Configure the Network Parameters With the client adapter card and the drivers and utilities installed, you next need to configure the system so that you can establish radio communication and pass
Do not overtighten. On Red Hat and other distributions that include the linuxconf utility, you should use this utility to configure DHCP on the computer. Click on "Load Firmware". Browse to the X:\cisco\PCI-PCM\Firmware folder and select the pcx500b.IMG firmware file. Once it flashes, you are done and can proceed to getting the driver working in the Home Skip to content Skip to footer Worldwide [change] Log In Account Register My Cisco Cisco.com Worldwide Home Products & Services (menu) Support (menu) How to Buy (menu) Training & Events
Red Hat 7.1 systems have three installation choices, with Option 1 being the easiest and most recommended. this contact form Install a PC Card Before you begin, examine the PC card. or would upgrading to FC2 be enough? Next, Windows will attempt to discover devices. You must be careful here or the live CD will fail to start up. (If the live CD fails to start up and you
Red Hat and other distributions that use linuxconf should use that utility to tell the operating system that the airo.o file is to be loaded for the PCI card. Complete these steps to configure the SSID on the client: At a command prompt, type acu to start the Aironet Client Utility (ACU). This can damage both the card and the slot. have a peek here Unpack the archive by using the tar command.
Type the IP address of the default gateway. Install PCI Drivers If you use a PCI card rather than a PCMCIA card, some different steps apply. Find More Posts by finegan 06-26-2004, 09:50 AM #3 metalpenguin LQ Newbie Registered: Jun 2004 Location: Omaha, Nebraska Posts: 14 Original Poster Rep: Hello, /sbin/lsmod reports the following, Module
Example: Linux montecito 2.2.16-22 #1 Tue Aug 22 164906 EDT 2000 i686 unknown In this example, montecito is the computer name, and 2.2.16-22 is the kernel version. Previous versions of the Linux drivers allowed you to specify the directory to which the client utilities would be installed, but in version 1.5.000, the utilities acu, bcard, leapset, leapscript, and When the adapter is installed, the antenna connector and the LEDs face out of your computer and are visible when you replace the cover. Slackware distributions prior to 7.2 should add a line to the end of the /etc/rc.d/rc.modules file to load the driver.
Configure for DHCP If you want your computer's IP address to be assigned by DHCP and your network has a DHCP server, you must run a DHCP client utility. Want to know if that peripheral is compatible with Linux? This requires the presence of compilation tools (such as gcc) but does not require the complete compilation/replacement of the installed kernel. Check This Out Cheers, Finegan finegan View Public Profile View LQ Blog View Review Entries View HCL Entries Visit finegan's homepage!
Get the Cisco driver. 2. Proceed to Set Utility Permissions. One end has a dual-row, 68-pin PC card connector. For Config mode, select Dhcp.
Finish the Installation Once the driver installation and utility configuration are complete, you can restart the network services or simply reboot. Shown here is an installation that requires Plug-and-Play BIOS support. Upgrade to 2.4.26 by hand. 3. I found it was difficult to do this, so I put together a live CD that accomplishes it. It has a few bugs but will work. You will need a Windows
You can follow any responses to this entry through the RSS 2.0 feed. See the man page for the shell you are using for the correct syntax. Configure the IP Address After you configure the radio-related aspects of the network, you need to configure the IP addressing. Warning! "Eth0 has an alias to module airo.o in modules.conf instead of currently loaded module airo!" metalpenguin View Public Profile View LQ Blog View Review Entries View HCL Entries Find
For optimal reception, position the antenna so it is straight up. The driver and client utility installation is complete. And I know you can't change the firmware under Linux, at least I've never heard of it... If you have a Cisco Aironet Series Wireless LAN Adapters CD-ROM containing the drivers and utilities, insert it into the CD-ROM drive of your computer and go to the Linux directory
The PCMCIA driver installation is now complete. I just realized the problem... Install the Drivers and Utilities Installation Notes You must be logged in as root or otherwise have superuser rights in order to perform the installation. Home Skip to content Skip to footer Worldwide [change] Log In Account Register My Cisco Cisco.com Worldwide Home Products & Services (menu) Support (menu) How to Buy (menu) Training & Events